Meyer® snow plow parts
Fisher® snow plow parts
Western® snow plows
Cutting edges

Strobe Bar Lights
Snowplow Lights
Dashboard Covers
Salt Spreaders
New innovative items
Pumprebuildingservice
Meyer® snow plow
Troubleshooting guide

"Sale Items"

Salt Spreader Installation Instructions

Mill Supply, Inc.
19801 Miles Rd.
Cleveland,OH 44128

Toll Free
PH#  800-888-5072
FX#  888-781-2700
Local
PH# 216-518-5072
FX# 216-518-2700

Magnum SUV and Pickup Hopper Salt Spreaders

Magnum Receiver Salt Spreaders made by Imperial have incorporated a better idea for long lasting operation. Imperial completed an exhaustive study of light-to-medium duty salt Spreaders and found the most common problem was the transmission. Sixty percent of field complaints involved drive mechanisms that would stick or stall. Nearly 40% of users polled had problems with auger power and 27% experienced control or wiring problems. Knowing the weak spots, Imperial set out to eliminate them in the MAGNUM series. These units will spread #1 rock salt, calcium chloride and other ice melting materials in a spread pattern more than 40 feet across.

Weight Capacity: 350 Pounds
Cubic Capacity: 5.75 cu ft.
Hopper Material: 304 Stainless Steel or Polyethylene
Empty Weight: SS - 130 pounds, Poly - 120 pounds
Mounting Method: Hitch, 2 inch receiver

Dimensions:
Stainless Steel - 33"H x 49"W x 30"D
Polyethylene - 35.5"H x 49"W x 30"D

Standard Equipment: Wiring harness, Variable speed controller with on/off & burst positions, Two ratcheting tie-down straps

Professional Salt Spreaders with Large 10.75 Cubic Ft. Capacity
Hopper Salt Spreaders with Hinge Mount or Flat Bed Mount Options

At the heart of the Magnum Salt Spreaders is a direct drive auger/impeller. There is no gear drive to rob power from where it is needed and no drive lubricant to turn to molasses in extreme cold. No gears, no lubricant—you get 75% more auger power, the best on the market! The auger and impeller are mounted directly to the motor shaft. No binding from power change-of-direction.

Features:

• Powder coated frame components
• Stainless steel impeller
• Motor lead location prevents accidental damage from below
• Low loss electrical harness
• Watertight connectors
• Stainless steel motor shaft
• Motors are protected with special shaft seals and have double seal bearings
• Variable speed control
• Weight Capacity: 750 Pounds
• Cubic capacity: 10.75 cu ft.
• Hopper Material: 304 Stainless Steel or Polyethylene
• Empty Weight: SS - 220 pounds, Poly - 205 pounds

Mounting Methods:
PICKUP HINGED MOUNT - Mounts to pickup bed and bumper; drilling required for bumper. Allows access to pickup bed by hinging to either side.

FLAT BED MOUNT - Triangulated support frame mounts to flatbed surface. Requires drilling of flatbed to accept mounting bolts (not included).

Overall Dimensions:
HINGED MOUNT - Stainless Steel 41"H X 25" D
Polyethylene 44 1/2"H X 25x" D (width adjusts to any full size pickup)
FLAT BED MOUNT - 49"H x 54"W x 43"D

Standard Equipment: Wiring harness, Variable speed controller with on/off & burst positions, Mounting hardware,
Two Year Warranty

SAND/SALT SPREADERS* *(can be converted for SAND with 354-0550 kit)

NEW STYLE HEAVY-DUTY PROFESSIONAL
SUV TAILGATE SALT SPREADER

HEAVY DUTY PROFESSIONAL
SUV TAILGATE SPREADER

1. SUV PRO MODEL

2" RECEIVER MOUNT
30 FEET MATERIAL SPREAD

• Rugged black thermoplastic hopper w/orange powder coated steel frame.
• Designed to hold 330 lbs. of #1 rock salt, or similar same size material.
• Spreads up to 30 feet wide — ideal for driveways and small parking lots.
• Heavy-duty sealed ball bearing motor with in-cab variable speed control.
• Fold-away feature. Release hitch pin to drop spreader out of way.
• Comes complete with all mounting hardware for 2" receiver hitches.
•  Dimensions: 40.5"H x 22.5"W x 20.5"D

• Mount on 2"receiver
• 330 lb. capacity
• Variable Speed - Hard wired
• Spreads material 30 feet
• Fold-away feature
• Ideal for driveways & lots
• UPSable

The SUV Tailgate Spreaders on this page includes a foldaway feature.  Simply release a hitch pin, and the spreader rotates down away from the rear door or tailgate for easy cargo access, without removing the spreader.

Part No.        Description

332-0025      Spinner Hub Weldment

Tailgate Salt Spreaders

Low Profile Salt Spreaders

Low Profile Tailgate Salt Spreaders

332-0060 - Low Profile Tailgate Spreader
This low profile tailgate spreader allows for full rear view from the vehicle.  Holds 800 lbs. of #1 rock salt or similar material.  The 12 volt motor is housed in a sealed motor chamber inside the hopper maximizing its protection from salt and other elements.  Powder coated frame and rugged thermoplastic hopper provide exceptional corrosion resistance.  Material flow and spread width, from 3' to 30', are controlled from an in-cab electronic spreader control panel. Comes complete with all mounting hardware.

Low Profile Tailgate Spreader and Replacement Parts
   LOC             PART NO.                  DESCRIPTION    

Wintergate Spreader Mount
354-0020 - Add the optional Wintergate Spreader Mount to the 332-0050 or 332-0060, and enjoy the benefits of easy access to the pickup truck bed.  Designed with adjustable telescoping rails that accommodates any pick-up truck width.  Now you have access to the bed of your pick-up without removing the spreader.   With the removal of two quick pins you can rotate the entire spreader out of the way for full bed access. 

332-0061 Spreader Mount
This mount will allow you to mount and dismount the 332-0050 and 332-0060 spreader quickly and easily.  Designed to fit 2" receivers. Will work on most pick up trucks regardless of tailgate widths.

SUV Tailgate Salt Spreaders

354-0300 - Tailgate Spreaders that mounts on 2" receiver mount. Ideal for the home owner/ residential user. The adjustable spread path is designed for one pass coverage of driveways and access roads.

DIMENSIONS: 40.5"H x 22.5"W x 20.5"D
WEIGHT: 66 pounds

• Features an attractive and rugged thermoplastic black hopper and orange powder coated mounting frame.
• Heavy-duty 12-volt Spreaders motor is housed in a sealed motor chamber.
• Material flow up to 10 feet controlled from an in-cab on-off control.
• Ultra-smooth hopper interior and auger provides material transfer by channeling it to the stainless steel-lined hopper throat and stainless steel spinner, providing an even flow of material without the need of expensive auger add-ons or vibration kits.
• Capacity: 300 pounds #1 rock salt or similar material.
• Mounting: comes complete with all mounting hardware for 2" receiver hitch and cigarette plug adapter.

Hopper Sand & Salt Spreaders

4 MODELS
SCH-096C
SCH-096CX
SCH-O96SS
SCH-096SSX

CLICK to see details!

Hopper Sand & Salt Spreader

4 and 4.5 Yard Stainless Steel Salt & Sand Spreaders
Designed for dump bodies & flat bodies with a GVW chassis of 15,000 to 20,000 lbs. and is available with either hydraulic motor drive or 10-1/2 H.P. gas engine.

1.8 & 2.3 Cu.Yd. Gas Poly/Steel/Stainless Steel Hopper Salt & Sand Spreaders

All hopper spreaders are completely self-contained, ultra-durable spreader units designed for ice and snow control. The rugged design allows for use with salt, sand and other materials. The complete assembly mounts easily on pickup, dump and platform trucks making it ideal for multiple users.
STEEL/STAINLESS STEEL MATERIAL HOPPER  – Electrically welded 12-gauge ends and steel sides sloped at 450 are constructed with channel formed top edges. 12-gauge vertical supports add extra strength. Uses a single lift point on the cross support beam for easy loading and unloading. The floor is 10-gauge steel.
 POLYMER MATERIAL HOPPER  – Molded double-wall polymer unibody spreader with smooth angled walls. Features integrated positive position mount systems plus 4 piece tie down kit. 
CONVEYOR – The conveyor is made of 12" wide all-steel pintle chain with 3/16"x 3/4" cross bars. Chain strength is 11,000 lbs. per strand; 22,000 lbs. total weight. The drive sprockets are 6 tooth cast iron on a 1-1/8" diameter shaft. Conveyor chain adjusts 3-1/2". The drive shaft has sealed, self-aligning ball bearings with grease fittings. The idler drum has 1" dia. ball bearings.
CONVEYOR GEAR CASE – Constructed of aluminum bronze, worm gear is hardened steel and ground. Housing is made of durable cast iron. Gear ratio is 20:1 with 1" input shaft and 1-1/8" output shaft on tapered roller bearings.
FEEDGATE – Lever operated with a friction lock for accurate adjustment.
SPINNER CHUTE ASSEMBLY  – A polymer disc with four fins is connected to a 3/4" diameter shaft secured on two pillow block bearings. The spreading material is guided from the conveyor to the spinner plate through an enclosed
12-gauge chute with internal and external deflectors. Adjustable deflectors allow for complete directional spread control and full or compact spread. Total spread radius ranges from 2' to 25'. The extra wide rear deflector protects the rear and under carriage of the vehicle.
ENGINE – Heavy-duty 10.5 horsepower Briggs & Stratton gas engine. Engine comes equipped with alternator and 12 volt electric starter with in-cab start/stop and electric throttle control (standard).
ELECTRIC THROTTLE CONTROL – Allows for full-range of throttle settings, including idle and full choke, via the in-cab hopper control box. Use of electric throttle control eliminates cable freezing, binding and breaking.
CLUTCH – 12 volt DC electric clutch has a three-position in-cab switch for greater control.  Also allows for low speed operation and spot spreading.

Part No.           Description             96" Models are 1.8 Cubic Yard Capacity — 120" Models are 2.3 Cubic Yard Capacity           Shipping Wt.

            ** Overall Length 137"Capacity Struck 2.3 cu.yd., Capacity Rounded 2.7 cu.yd. Width 47", Height  32-1/2"

Stainless steel models feature high-quality grade 304 stainless steel components, including: Hopper, Hopper Supports, Hopper Floor, Gussets, Spinner Chute Assy, Deflectors, Engine Hood, and Inverted V.

Rotationally molded double-wall polymer unibody spreader with smooth angled walls to maximize material flow. Features high-quality grade 304 stainless steel Spinner Chute Assembly, Deflector and Engine Hood.

Electric Polymer "Salt Dogg" Spreader

IDEAL FOR MEDIUM AND HEAVY DUTY COMMERCIAL APPLICATIONS.

Standard items included with the Salt Dogg are a black powder coated steel top screen, inverted "V", spreader tie-down kit and poly-vinyl tarp with tie-downs.

The Electric Polymer Salt Dogg Spreaders are completely self-contained, ultra-durable spreader units designed for ice and snow control. The rugged design allows for use with salt or salt/sand mix. The complete assembly mounts easily on pickup, dump and platform trucks, making it ideal for municipalities, shopping malls, industries, hospitals and private contractors.

MATERIAL HOPPER – Rotationally molded double-wall polymer unibody spreader with smooth angled walls to maximize material flow. Features integrated positive position mount system plus 4-piece ratchet tie-down kit. No drilling required. Molded fork slots in hopper (1500 series only) makes for easy one man installation and removal; requires extended forks, or lift either series with 4-point tie downs.
AUGER – Screw-type auger system travels the length of the hopper floor, providing maximum material flow at a continuous rate. An independent spinner/auger controller allows for both independent spinner speed and an infinitely adjustable ratio between spinner and auger.
MATERIAL FLOW/OUTPUT – Salt, 2.2 cu. ft. / minute; Salt-Sand, 1.3 cu. ft. / minute. Spread width is variable from 5 to 38 feet.
SPINNER CHUTE ASSEMBLY – An 11.5" polymer disc with four fins is connected to a 3/4" diameter shaft. The spreading material is guided from the stainless steel trough to the spinner plate through an enclosed heavy-duty polymer chute and spinner assembly with an external deflector. The extra-wide adjustable deflector protects the rear and under carriage of the vehicle, and allows for complete directional spread control and full or compact spread. Total spread path ranges from 5' to 38'. A convenient spring-latch locking mechanism allows the spinner assembly to be easily removed for cleaning/storage.
ELECTRIC MOTORS – Two ultra-quiet 12-volt DC direct-drive motors power the auger and spinner, and are encased in a heavy-duty poly housing along with the independently powered vibrator. The wiring harness is constructed of 10-gauge automotive wire with non-combustible sheathing
(-50° to -105° C). An in-cab console features independent controls for the auger, spinner and vibrator.
STANDARD EQUIPMENT – 1/4" black powder coated steel top screen. Heavy-duty polyvinyl tarp with reinforced corners and tie-down kit. Heavy-duty 12 VDC vibrator, rated at 210 foot pounds for maximum performance. Spreader hold-down kit.
The Salt Dogg mounts easily on pickup, dump and platform trucks making it ideal for municipalities, shopping malls, industries, hospitals and contractors.

354-0400/354-0425: 1.5 Cubic Yard, 92" (requires 77" minimum bed length. Fits all 8' beds and most standard 6' beds); Capacity Struck, 1.45 cu. yd.; Width, 50.5"; Height, 37.5"; Recommended use, 3/4 or 1-Ton trucks.
354-0430/354-0435: 2.0 Cubic Yard, 96" (requires 77" minimum bed length. Fits all 8' beds and most standard 6' beds); Capacity Struck, 2.0 cu. yd.; Width, 47.5"; Height, 40"; Recommended use, 3/4 or 1-Ton trucks above 8,500 lbs. GVWR.

Electric Polymer "Salt Dogg" Salt & Sand Spreader

    354-0420          Replacement Vibrator, 12VDC                                                                5.3 lbs.

2" RECEIVER HITCH

Ideal for Receiver Mount Salt Spreaders weighing up to 350 lbs. Can be mounted on any flat surface, under any bumper, or mount upside down on a flat bed. 3500 lb. towing capacity.

354-0510
Three Point Tractor Adaptor

THREE POINT TRACTOR ADAPTOR

Weight Capacity: 500 lbs.

Accessory weight: 32 lbs.

Mounting Method: Uses three-point tractor accessory connections to provide mount for standard 5.75 Cubic Feet Magnum Spreaders.

Adapter Dimensions: 17.5H x 10.5W x 32L

Construction: Black painted steel, .25 thick

354-0515
Flatbed Utility Mount Adaptor

FLATBED UTILITY MOUNT ADAPTOR

Weight Capacity: 500 lbs.

Accessory weight: 18 lbs.

Mounting Method: Bolts to any flat surface. Can mount on bottom or top of bed. Used with the 5.75 cubic feet Magnum Spreaders. Requires drilling into bed. Bolts not included.

Adapter Dimensions: 2.2"H x 16"W x 16"D

Construction: Powder coated steel, .25" thick

BALL MOUNT

• Allow receivers to be used as weight carrying hitches
• 6000 lbs GTW
• Able to raise or lower ball height
• Fits all 2 x 2 Receivers
• Black in Color

UB-612-B - 6" drop, 5" rise, 12" length
UB-409-B - 4" drop, 2" rise, 9" length
UB-210-B - 2" drop, 3/4" rise, 10" length

TRI-BALL HITCH

Tri-ball Hitch. Rotate the 2” shank to get the correct ball size for your trailer. Choose from three sizes
1-7/8", 2" and 2-5/16".

CLASS III RIGID HITCHES

• Frame Mounted
• 5 Year Warranty
• 2" x 2" Receiver Tube
• Black Powder Coat Finish
• Custom Designed for Quick Installation
• Carrying Weight - Up to 5,000 lbs. GTW & 500 lbs. TW

Applications for:

CHEVROLET PICKUP
FORD PICKUP
DODGE PICKUP

BACK-UP ALARMS

If you plow and own a salt Spreaders, be sure you have a back alarm mounted to your vehicle. Almost half the time you are plowing or spreading salt in a driveway or a parking lot you are in reverse. Warning local pedestrians from danger is a necessity. Mill Supply, Inc. carries a variety of back alarms to choose from.

87-030 - Bulb Combination Back Alarm Replaces your standard 1156 Back-up Lamp

87-034 - Bulb Combination Back Alarm Replaces your standard 3156 Back-up Lamp