• Discount Snow Plow Home
• Specials
New Products
• Blizzard Snow Plow Parts
• Boss Snow Plow Parts
• Curtis Snow Plow Parts
• Diamond Snow Plow Parts
• Fisher Snow Plow Parts
• Meyer Snow Plow Parts
• Sno-Way Snow Plow Parts
• Western Snow Plow Parts
• Salt Spreaders
  Buy Spreaders Now Salt Spreader Info Tailgate Spreaders Bed Mount Spreaders 1.8,2.3 and 4.5 Cubic Yard Spreaders
• Back Alarms
• BackRack Products
• Discount Truck Parts
• Snow Plow Lights
• Snow Plow Test Kit
• Strobe Bar Lights
• Timbren Suspension Springs
• Installing Your Plow Lights
• Pump Rebuilding Service
• Search This Site
• Search by Part Number

Tailgate Mount Spreaders

With 6 different tailgate spreaders you are sure to find the exact model you need. Mill Supply carries Buyers brand tailgate spreaders. We rate the spreaders by the amount of weight in salt the spreader will hold. The weights vary from 330 pound all the way up to 825 pounds for tailgate spreaders. The larger capacity spreaders are rated on how many cubic yards of material they will hold. See below for a more complete description on larger spreaders.

For the home and small business owner we recommend the SUV standard or pro model. This small spreader mounts into your 2" receiver tube (the standard model will even mount into a 1-1/4" receiver) and will hold four 80 lb. bags of salt at one time. The standard model uses a manual upon/close gate type system. Once the gate is adjusted the salt flows out. To spread the salt you have an on/off switch inside the vehicle to operate the spinner plate that spreads the salt. This bare minimum unit will spread salt in a 12 foot wide pattern.

A step up from the standard model is the SUV PRO model. The unit itself is the same size but comes with a variable speed motor that runs a spinner auger. This unit will not only completely stop the flow when not running but will also spread the material up to 30 foot with its upgraded motor. It also has an in-cab controller to either slow down or increase the speed depending on the width of throw you may need.

The next step up would be our 600 and 800 pound capacity spreader that uses the same motor and controller as the SUV PRO model but has a larger capacity. These are commercial spreaders and are great for the snow plower that has contracts for a number of driveways or parking lots. The big difference between these two models is the 600 lb. unit is taller and has the motor underneath the unit and the 800 lb. spreader is low profile and has the motor tucked away inside the hopper.

The standard mount that comes with these spreaders requires drilling into your step bumper and bed. There is a kit that will allow quick mounting and no drilling. Order part number 332-0061 if you have a 2" receiver and don't want to drill into your bumper and bed. This still eliminates you opening your tailgate without removing your spreader but that has been overcome also. There is a 'Wintergate Mount' that will allow your spreader to swing to the side and give access to your pickup bed. Again, drilling will be required but it may be your only option if you need to get into the bed of your pickup through the tailgate. Order part number 354-0020 for the Wintergate mount system.

The next newer designed model Buyers came out with is a little larger in capacity, has the low profile design for better viewing and a vibrator to keep the material flowing instead of an auger attached to the spinner plate. This 10 cubic foot model (our number 332-0070) has the motor hidden inside the hopper. This spreader does not have a welded steel frame but is a double walled poly construction to lighten the weight of the unit. Material spread is from 3 ft to 30ft controlled from an in cab electronic controller. (Buyers uses the same in-cab controller for all its smaller units, only the SUV standard model does not come with a controller.) It also can be mounted without drilling by using your existing receiver hitch (or the flat surface on your step bumper) and arms that extend to the stake pockets on your bed.

Introduced in 2010 is the 11 cubic foot, 825 pound capacity, V-Box spreader that is: low profile, has the hidden motor, a vibrator and horizontal auger for all the features in one spreader. With the open-auger design of this new spreader you can now spread salt/sand mixtures. It mounts into a class 4 receiver with no bed drilling. It has very steep walls to keep material flowing even without the vibrator that is included. Sports a dual action lid so you can load if from the bed of the truck or from the ground. So if you have bags of salt in the bed of your truck just jump in, tilt the lid to the back and load up. This is by far the best design yet for a tailgate spreader but has a price to match. Our part number is 380-0100.

To get the best deals on all our spreaders be sure to order them in the fall season. We always run great sales from October thru the month of December.

Buy Your Salt Spreader Now!

• • .75-2.2 Cu. Yd. Polymer Hopper Spreaders
  • .75 Cu. Yd. Electric Poly Hopper Spreader
  • 1.8-2.3 Cu. Yd. Gas Steel Hopper Spreaders
  • 10 Cu. Ft. Tailgate Spreader
  • 3 Cu. Yd. Electric Poly Hopper Spreader
  • 300-350 lbs Capacity Salt Spreaders
  • 4-4.5 Cu. Yd. Stainless Steel Hopper Spreader
  • 4.0 Cu. Yd. Electric Poly Hopper Spreader
  • 600 lbs Capacity Tailgate Spreader
  • 750 lbs Capacity Tailgate Spreader
• • 800 lbs Capacity Tailgate Spreader-Low Profile
  • 825 lbs Capacity Tailgate Spreader-Low Profile
  • Hopper Spreader Replacement Parts
  • Electric Drive Under Tailgate Spreader
  • Liquid Spray Systems
  • Old Style Salt Spreader Parts
  • Salt Spreader Parts for Western
  • Salt Spreader Vibrator Kit
  • Snow-Ex Spreader Replacement Parts
  • Walk Behind Salt & Sand Spreader Parts
  • Walk Behind Salt & Sand Spreaders